• High Impact Resistance
• Temperature Range of -60 to 270 F
• High Rigidity
• Ductility of Softer Lower Modulus Plastics
• Transparent Clear

Commonly referred to as Lexan, Polycarbonate is a thermoplastic used in many applications that require high impact strength, a large temperature service range, excellent electrical properties, and dimensional stability. Polycarbonate Sheet is smooth and clear. Normal forming temperature of Polycarbonate is 375F (190C).

List Price: $ 13.04

Price: $ 13.04

• Abrasion Resistant
• Low coefficient of Friction
• Good Energy Absorption
• Resists Stress Cracking
• Moderate Temperature Rating

High Density Polyethylene (HDPE) is high impact strength with a higher temperature rating than Low Density Polyethylene. It has higher tensile strength, good energy absorption, abrasion resistance and resists stress cracking. HDPE has a low coefficient of friction and is self lubricating. Applications include low speed bearings, tank/chute/bin linings, packing rings in chemical applications. HDPE is in the family of polyolefin’s.

List Price: $ 34.24

Price: $ 34.24

• Molybdenum disulfide creates a superior bearing and bushing
• Resists Common Solvents, Esters, Ketones, Alkali’s and Dilute Acid
• No lubrication required
• 7.5 to 8.5 percent water absorption
• Good choice for inaccessible bearing surfaces

This excellent combination of wearing resistant qualities of virgin Nylon 6/6 with the antifriction capability of molybdenum disulfide creates a superior bearing and bushing material. Useful wherever lubrication is undesirable, when the part is located in a position that is difficult to service. Nylon Molybdenum disulfide resists common solvents, hydrocarbons, esters, ketones, alkalies and dilute acids. Not resistant to phenol, formic acid or concentrated mineral acids. Tested for moisture absorption using ASTM D-570 specifications: 1.2-2.5 percent when saturated over a 24-hour period; 7.5-8.5 percent maximum saturation.

List Price: $ 8.48

Price: $ 8.48

• Low Deformation Under Load
• Low Coefficient of Friction
• Excellent Dimensional Stability
• FDA and USDA Compliant
• Chemically Inert

Fluorosint 500s unique properties are the result of a proprietary process in which synthetically manufactured mica is chemically linked to PTFE. This bonding results in properties not normally attainable in reinforced PTFE. It has a continuous use temperature to 500 F. When compared to PTFE it has a higher load carrying capability, and lower coefficient of thermal expansion. Fluorosint 500 is a structural/seal grade filled with enough mica to produce a thermal expansion 15percent less than unfilled PTFE.

List Price: $ 47.85

Price: $ 47.85

• Excellent Bushing and Bearing Material
• 1/8 the Weight of Bronze
• Corrosion Resistant
• Easily Maintained
• Easily Fabricated

Nylatron GS Nylon 6/6 is a molybdenum disulphide (MoS2) filled nylon offering improved strength and rigidity. It exhibits excellent wear and abrasion resistance and is 1/8 the weight of bronze making it an excellent replacement for metal bushings. It is easier to fabricate and maintain than metal.

List Price: $ 15.99

Price: $ 15.99

• Heat Deflection Temperature Under Load is 200 F
• Resists Common Solvents, Esters, Ketones, Alkali’s and Dilute Acid
• Tough and Impact Resistant
• Low Coefficient of Friction
• Easily Machined

Nylon 6/6 Rods and Sheet are typically used as material for insulators, shaft bearings and bushings, wear strips, hinges, gears, and general fixturing. Heat deflection temperature at 264 PSI: 200F (93C). Color: Natural.A tough general purpose plastic with outstanding resistance to organic chemicals, acids and alkalis, Nylon 6/6 wears well against other surfaces and has a low coefficient of friction. It is readily machinable and may be milled, turned and cut with conventional machine tools. It does exhibit some dimensional swelling in wet applications, (up to 10 percent ) which should be taken into account with its use.

List Price: $ 15.49

Price: $ 15.49

• Temperature Range -348 to 400 F
• Extreme Chemical Resistance
• Lowest critical surface energy of all plastics
• Lowest Refractive Index of All Plastics
• Extremely low dielectric constant and dissipation factor

Teflon FEP Rod has excellent chemical, thermal, and electrical stability. It retains a high percentage of its useful properties from cryogenic to elevated temperatures -348 F to 400 F. It has the lowest critical surface energy of all plastics, which makes it an excellent water and oil repellent for non-stick and mold release. Teflon FEP has an extremely low dielectric constant and dissipation factor. Excellent resistance to UV, Ozone, and has the lowest refractive index of all plastics. Typical applications include electronic bobbins, piping material for high temperature use, spring actuated seals, gaskets, packing and valve seats.

List Price: $ 18.93

Price: $ 18.93

• Low Water Absorption
• Excellent Wear Resistance
• Very Low Porosity
• High Flexural Modulus
• Good Impact Resistance

PET (Polyethylene Terephthalate) is an unreinforced, semi-crystalline thermoplastic Polyester. It has excellent wear resistance, essentially no porosity and low absorption. Low coefficent of friction, high flexural modulus and superior dimensional stability make it a versatile material for designing mechanical and electromechanical parts. Applications include food and beverage handling, printing inks, and water purification products.

List Price: $ 19.65

Price: $ 19.65

• High Impact Resistance
• Temperature Range of -60 to 270 F
• High Rigidity
• Ductility of Softer Lower Modulus Plastics
• Transparent Clear

Commonly referred to as Lexan, Polycarbonate is a thermoplastic used in many applications that require high impact strength, a large temperature service range, excellent electrical properties, and dimensional stability. Polycarbonate Sheet is smooth and clear. Normal forming temperature of Polycarbonate is 375F (190C).

List Price: $ 9.23

Price: $ 9.23

• High Impact Resistance
• Temperature Range of -60 to 270 F
• High Rigidity
• Ductility of Softer Lower Modulus Plastics
• Transparent Clear

Commonly referred to as Lexan, Polycarbonate is a thermoplastic used in many applications that require high impact strength, a large temperature service range, excellent electrical properties, and dimensional stability. Polycarbonate Sheet is smooth and clear. Normal forming temperature of Polycarbonate is 375F (190C).

List Price: $ 9.23

Price: $ 9.23