PETROSCRAPS.COM

Ultem 1000 Round Rod, Beige, 1″ OD, 12″ Length PEI will withstand continuous temperature of 390 F under load.Is rated UL 94 VO and is generally accepted by the FAA for aircraft interiorsPEI has found use in the Medical Device Market because of its heat and radiation resistanceIt is prone to stress cracking in chlorinated solvents.It is soluble in partially halogenated solvents but resistant to alcohols, acids and hydrocarbon solvents. Polyetherimide (PEI) is an amorphous, amber-to-transparent thermoplastic with similar characteristics to PEEK’s. Relative to PEEK, it is cheaper, but less temperature-resistant, and lower in impact strength. It is prone to stress cracking in chlorinated…. Click Here to Read More

Ultem 1000 Sheet, Beige, 1/4″ Thick, 12″ Width, 12″ Length USP Class VIIs rated UL 94 VO and is generally accepted by the FAA for aircraft interiorsPEI has found use in the Medical Device Market because of its heat and radiation resistanceIt is prone to stress cracking in chlorinated solvents.It is soluble in partially halogenated solvents but resistant to alcohols, acids and hydrocarbon solvents. Polyetherimide (PEI) is an amorphous, amber-to-transparent thermoplastic with similar characteristics to PEEK’s. Relative to PEEK, it is cheaper, but less temperature-resistant, and lower in impact strength. It is prone to stress cracking in chlorinated solvents. It is available under the…. Click Here to Read More

PEEK 1000 Sheet, Tan, 3/4″ Thick, 6″ Width, 6″ Length Exceptional Heat ResistanceBio CompatibleExcellent Abrasion ResistanceExcellent Chemical resistanceMelt Processable PEEK is a semicrystalline thermoplastic with extraordinary mechanical properties. The Young’s modulus is 3.6 GPa and its tensile strength 90 MPa. PEEK exhibits two glass transition temperatures at around 140 C (284 F) and around 275 C (527 F), depending on cure cycle and precise formulation. PEEK melts at around 350 C (662 F) and is highly resistant to thermal degradation. The material is also resistant to both organic and aqueous environments, and is used in bearings, piston parts, pumps, compressor plate valves, and…. Click Here to Read More

Seventh Generation Bathroom Tissue, 1-Ply Sheets, 1000 Sheet Roll (Pack of 48) Ships in Certified Frustration-Free PackagingMade of 100-percent recycled paper (minimum 80-percent post-consumer)Whitened with an environmentally-safe processFree of dyes, inks, and fragrancesOne-ply bathroom tissue is soft and strong, safe for septic systems and ideal for low-flow toilets Seventh Generation Bathroom Tissue is made from 100% recycled paper, with a minimum of 80% post consumer materials. Our paper is whitened with an environmentally safe process never with chlorine bleach. Our Bathroom Tissue is hypo-allergenic, safe for septic systems, ideal for low-flow toilets and contains NO dyes, inks or…. Click Here to Read More

Nylon Mesh Sheet, 1000 Microns Square Opening, 59% Open Area, 515 Microns Thread Diameter, 12″ x 12″ Exceptional StrengthGamma, Steam, ETO SterilizableNitex BrandMesh Opening Size 1000 MicronsPrecise Opening Size Nylon screen cloth – 6/6: Exceptionally strong and suited for countless sifting, straining, and filtration applications. Provided in the small sizes so useful in laboratory or shop. Can be gamma, steam and Eto sterilized. Slight yellowing may occur during steam sterilization, but will not significantly affect physical properties. List Price: $ 9.39 Price: $…. Click Here to Read More

These are the same straws that you get at the bar.Sold by the box, 1000 (approx) per box.5″ length.Must have for your bar.Comes in red only. Product DescriptionThese are the same straws that you get at the bar with your mixed drink. Sold by the box, 5-inch length. In stock and ready to ship. Features: 1000 (approx) per box. Specs: Dimensions: 5″ L. Color:…. Click Here to Read More

USP Class VIIs rated UL 94 VO and is generally accepted by the FAA for aircraft interiorsPEI has found use in the Medical Device Market because of its heat and radiation resistanceIt is prone to stress cracking in chlorinated solvents.It is soluble in partially halogenated solvents but resistant to alcohols, acids and hydrocarbon solvents. Product DescriptionPolyetherimide (PEI) is an amorphous, amber-to-transparent thermoplastic with similar characteristics to PEEK’s. Relative to PEEK, it is cheaper, but less temperature-resistant, and lower in impact strength. It is prone to stress cracking in chlorinated solvents. It is available under the tradename Ultem, a registered trademark of…. Click Here to Read More

USP Class VIIs rated UL 94 VO and is generally accepted by the FAA for aircraft interiorsPEI has found use in the Medical Device Market because of its heat and radiation resistanceIt is prone to stress cracking in chlorinated solvents.It is soluble in partially halogenated solvents but resistant to alcohols, acids and hydrocarbon solvents. Product DescriptionPolyetherimide (PEI) is an amorphous, amber-to-transparent thermoplastic with similar characteristics to PEEK’s. Relative to PEEK, it is cheaper, but less temperature-resistant, and lower in impact strength. It is prone to stress cracking in chlorinated solvents. It is available under the tradename Ultem, a registered trademark of…. Click Here to Read More

Low Specific GravityHighly Resistant To ChemicalsMelting Temperature 320 FMesh Opening Size 1000 MicronsScreen Floats In Water Product DescriptionPolypropylene screen cloth offers great strength and stability, polypropylene has the lowest specific gravity (0.91) of any synthetic. Highly resistant to acids and alkalis as well as other chemicals. Polypropylene Screen Cloth has a melting temperature of 320 to 340F (160 to…. Click Here to Read More

Exceptional Heat ResistanceBio CompatibleExcellent Abrasion ResistanceExcellent Chemical resistanceMelt Processable Product DescriptionPEEK is a semicrystalline thermoplastic with extraordinary mechanical properties. The Young’s modulus is 3.6 GPa and its tensile strength 90 MPa. PEEK exhibits two glass transition temperatures at around 140 C (284 F) and around 275 C (527 F), depending on cure cycle and precise formulation. PEEK melts at around 350 C (662 F) and is highly resistant to thermal degradation. The material is also resistant to both organic and aqueous environments, and is used in bearings, piston parts, pumps, compressor plate valves, and cable insulation applications. It is…. Click Here to Read More

Exceptional Heat ResistanceBio CompatibleExcellent Abrasion ResistanceExcellent Chemical resistanceMelt Processable Product DescriptionPEEK is a semicrystalline thermoplastic with extraordinary mechanical properties. The Young’s modulus is 3.6 GPa and its tensile strength 90 MPa. PEEK exhibits two glass transition temperatures at around 140 C (284 F) and around 275 C (527 F), depending on cure cycle and precise formulation. PEEK melts at around 350 C (662 F) and is highly resistant to thermal degradation. The material is also resistant to both organic and aqueous environments, and is used in bearings, piston parts, pumps, compressor plate valves, and cable insulation applications. It is…. Click Here to Read More

Exceptional Heat ResistanceBio CompatibleExcellent Abrasion ResistanceExcellent Chemical resistanceMelt Processable Product DescriptionPEEK is a semicrystalline thermoplastic with extraordinary mechanical properties. The Young’s modulus is 3.6 GPa and its tensile strength 90 MPa. PEEK exhibits two glass transition temperatures at around 140 C (284 F) and around 275 C (527 F), depending on cure cycle and precise formulation. PEEK melts at around 350 C (662 F) and is highly resistant to thermal degradation. The material is also resistant to both organic and aqueous environments, and is used in bearings, piston parts, pumps, compressor plate valves, and cable insulation applications. It is…. Click Here to Read More